If you’re looking to reset your Kwikset smart lock, you’ve come to the right place! Kwikset offers a few different ways to reset your device, depending on the model of the lock. The general steps for resetting a Kwikset smart lock are as follows:
1. Start by gathering all the necessary materials such as a Phillips screwdriver, paperclip and a fresh 9-volt battery. Make sure you have a charged battery and check the expiration date on it if possible.
2. Remove the inside cover of the lock mechanism by unscrewing the screws with your Phillips screwdriver.
3. Locate the reset button, which is usually found near the back of the mechanism.
4. Insert a paperclip into the reset button hole and press it firmly for five seconds. You should hear a beeping sound from your lock to confirm that it has been reset.
5. Replace the inside cover and screw it back into place with your Phillips screwdriver.
6. Install a fresh 9-volt battery and make sure it is secure before closing up the lock’s outside cover.
7. Test out your lock to make sure it is working properly. If so, you have successfully reset your Kwikset smart lock!
If you’re still having trouble resetting your lock, contact Kwikset customer service for additional support. They can help troubleshoot any issues you may be experiencing with your device and walk you through the reset process if needed.
How do you program a Kwikset Smart Lock
Programming a Kwikset Smart Lock is a simple process that requires no tools or special technical knowledge. The key to successfully programming the lock is to follow the instructions provided in the user manual carefully.
Before you begin, make sure you have all necessary parts, such as batteries, a mastercode and programming code (if required). If your lock requires a programming code, you must obtain it from your locksmith or from Kwikset’s customer service department.
Once you have all the necessary components, start by inserting the batteries into the back of the lock and then pressing the “Program” button on the front of the lock. This will reset the lock, allowing you to program it to your desired specifications.
Next, enter your mastercode into the keypad and press “Enter”. Your mastercode is typically an 8-digit number that you can set yourself or have Kwikset provide you with one. Once entered, press “Enter” again and then select whether or not you want to program individual user codes or a single user code for all users.
If programming individual user codes, you must enter each user’s code into the keypad one at a time and press “Enter” after each one. Then press “Done” when finished. If programming a single user code for all users, enter it into the keypad and press “Enter” twice – once to confirm it and again to save it.
Once your codes have been programmed and saved, if desired you can also adjust other settings on your Kwikset Smart Lock such as auto-locking time, auto-unlocking time and alarm sensitivity. Consult the user manual for instructions on how to do this.
Finally, test out your new Kwikset Smart Lock to make sure it is responding properly before finalizing installation. Once satisfied with its performance, complete installation by securing it in place according to manufacturer instructions.
By following these steps carefully, you can easily program your Kwikset Smart Lock for secure access control at your home or business.
How do I find my Kwikset key code
If you have Kwikset locks in your home, you may be wondering how to find your Kwikset key code. A Kwikset key code is a unique code that identifies the lock and is used for rekeying or replacing lost keys. Finding your Kwikset key code can be a bit tricky, but there are a few methods you can use to get the information you need.
The first way to find your Kwikset key code is by taking off the lock’s cylinder and looking for the code stamped on the side of it. This should be printed with letters and numbers, and will be unique to each lock. If you can’t find the code on the cylinder, you can also look at the paperwork that came with your lock when it was purchased. This should have the code printed on it.
If you don’t have the paperwork or can’t find the code on the cylinder, another option is to contact a locksmith or a professional who specializes in Kwikset locks. They should be able to tell you what your key code is based on the make and model of your lock.
Finally, if all else fails, you can always contact Kwikset customer service directly and provide them with some basic information about your lock such as its make and model number. They should then be able to provide you with the correct key code for your lock.
Finding your Kwikset key code doesn’t have to be a difficult process. By following these simple steps, you should be able to get the information you need in no time at all!
How do I change the code on my Kwikset 955
Changing the code on your Kwikset 955 is a simple process that should only take a few minutes. The Kwikset 955 is a keyless entry system, allowing you to unlock and lock your door without the need for a key.
To begin, locate the programming button on your Kwikset 955. This will usually be a small button located somewhere on the inside of the unit. Once you have located the button, press it once. This will enter programming mode and the LED indicator light will blink twice.
Once programming mode has been entered, use a pen or paper clip to press and hold down the programming button for 10 seconds. During this time, you will hear three beeps from the unit before the LED indicator light turns off.
After this, enter your new 4-8 digit code into the keypad. The LED indicator will blink twice to indicate that it has accepted your code. Then press the “Program” button again to save your new code.
Finally, test out your new code to make sure it works correctly. Enter your new code into the keypad and wait for the LED indicator to blink twice to indicate that it has accepted your code. If it does not accept the code, try entering it again. Once you have confirmed that your new code works correctly, you have successfully changed the code on your Kwikset 955!
How do I reset my Kwikset 917 lock code
If you need to reset your Kwikset 917 lock code, there are a few simple steps you can follow to do so.
First, locate the program button on the inside of the lock. It should be located near the latch mechanism and will either be a small round or square button.
Then, insert the original key into the lock and turn it clockwise until it stops. Once this is done, press and hold the program button for 3-5 seconds until you hear a single beep. This indicates that the lock is in “programming mode”.
Next, remove the original key and enter your new 4-8 digit code. When done, press the program button once more to confirm your new code. You should hear two beeps which indicates that your new code has been successfully programmed into the lock.
Finally, test your new code by entering it into the lockset and turning the key counterclockwise. If it unlocks correctly, then you have successfully reset your Kwikset 917 lock code.
It’s important to note that if you make an error while programming your new code or if you need to reset it again in the future, simply repeat these steps and enter a new code.
By following these steps, you can easily reset your Kwikset 917 lock code and ensure that only those with access to your code can unlock it.
How do you unlock a Kwikset lock from the outside
Unlocking a Kwikset lock from the outside can be done in a few different ways depending on the type of lock you have. If your Kwikset lock is a traditional pin and tumbler lock, then you can use a key to unlock it. If it’s a more modern electronic or smart lock, then you can use a code to open it. In either case, there are some important steps to take before attempting to unlock the door.
Before unlocking any door with a key or code, make sure that the door is properly secured and that no one else is inside the room. If someone else is inside, they should be asked to leave before you attempt to unlock the door.
If you are using a traditional key, insert it into the keyhole and turn it until the lock opens. Be sure to only apply enough pressure to open the lock without breaking it. Once unlocked, pull the door open and make sure it closes securely behind you.
If you are using an electronic/smart lock, enter your code into the keypad or display on the outside of the door. Make sure that all of your digits are correct before pressing “enter” or “unlock” on the keypad. When done correctly, the lock should disengage and the door should open and close properly behind you.
It is important to remember that all locks should be kept secure at all times—whether locked or unlocked—to prevent unwanted access. If you are having trouble unlocking your Kwikset lock from the outside, contact a professional locksmith for assistance.
How do I change the code on my Kwikset SmartCode 913
Changing the code on your Kwikset SmartCode 913 is a relatively simple process. First, you’ll need to locate the programming button on the inside of the lock. It should be located near the bottom of the lock.
Once you’ve located the programming button, press and hold it for five seconds. This will activate the programming mode. After five seconds, you should hear a single beep indicating that the programming mode is active.
Next, enter your new four-digit code into the keypad. You can use any combination of numbers between 0000 and 9999. Once you’ve entered your new code, press the programming button again and you should hear two beeps indicating that the code has been successfully changed.
Your Kwikset SmartCode 913 should now respond to your new code when entering it on the keypad. If you ever need to change your code again, just repeat these steps from the beginning.
How do I delete all codes on Kwikset SmartCode
Kwikset SmartCode locks are a great way to keep your home secure. They offer you the convenience of keyless entry while still allowing you to easily control access to your home. But if you ever need to delete all codes from your Kwikset SmartCode lock, it can be a bit tricky.
Fortunately, deleting all codes from your Kwikset SmartCode lock is actually quite simple. Here’s what you need to do:
1. First, find the Programming Code for your Kwikset SmartCode lock. This is typically found on the back of the instruction manual that came with the lock, or inside the battery compartment.
2. Next, press and hold the “Program” button on the interior of your Kwikset SmartCode lock until you hear two beeps. This indicates that you have successfully entered Programming Mode.
3. Now enter your Programming Code into the keypad of your Kwikset SmartCode lock. The keypad will beep twice after you enter the code, indicating that you have successfully entered Programming Mode.
4. Once in Programming Mode, press and hold the “DEL” button for three seconds. This will delete all codes stored in the memory of your Kwikset SmartCode lock. You will hear two beeps after deleting all codes, indicating that the process was successful.
5. Finally, press and hold the “Program” button again until you hear two beeps; this will exit Programming Mode and return your Kwikset SmartCode lock to normal operation mode.
And that’s it! By following these five steps, you can easily delete all codes from your Kwikset SmartCode lock in no time at all. Keep in mind that once all codes are deleted, any existing codes will need to be re-entered for the lock to work properly again.